Directory
? 👈
Inch or
Metric
The main Navigation tabs at top of each page are Metric - inputs in millimeters (mm)
For Inch versions, directly under the main tab is a smaller 'Inch' tab for the Feet and Inch version.
Drop Down Menus have M for Metric Versions.
Help


Home
♻ 		Wall
Framing 		Baluster
Spacing 		All Centers
Spacing 		Hole
Spacing 		Fastener
Spacing 		Gable
Spacings 		Gable
Stud Lengths 		Kerf Spacing
Wood Bending 		Woodturning
Segments
Directory Inch Inch Inch Inch Inch Inch Inch Inch Inch
Circle
Centers 		Paving
Circles 		Masonry
Arch 		Tile Fit
Spacing 		Running
Set-out 		Paling Fence
Rails past Posts 		Panels or Palings
Between Posts 		Arched Fence
Paling Lengths 		Diminishing
Lengths At Angle 		Brick
Gauge
Inch Inch Inch Inch Inch Inch Inch Inch Inch

Wall Framing Calculator - Single Wall - Stud Spacing and Sheeting Fit (Width)

Wall Length
Sheet Width
Stud Centers
?
Assumes Nominal 2 x 4 = Actual size 1~1/2" x 3~1/2"
Assumes Nominal 2 x 6 = Actual size 1~1/2" x 5~1/2"
Studs 		Nominal
Stud Height
Rake Angle
?
Draws the diagram to scale.
Drag the 'Scale' slider to adjust Printed Scale.
End Stud Options
?
Orthogonal wall is at right angles to connected adjacent walls. The end studs are set in the width of adjacent wall studs, and sheeting extends to cover adjacent wall ends and meet at external corner.
?
With Gap, the second stud is adjusted to start 1 stud width in from wall end.
This will align studs so orthogonal (at right angles) wall studs meet to form internal corners.
?
Californian Corner has second stud on edge (at inside of wall) to form internal corner and allow space for insulation at wall ends.
See diagram below.

Length Angle Scale

Wall Framing Calculator - Stud Spacing and Sheeting Fit
Running measurements are and on - From start of wall to near side of each stud.
Make the mark, then put an X on the far side to denote stud placement: Start of Wall → 
|X     |X      |X      |X      |X      |X

Mark-out

Wall Framing Lumber Quantities - Total Wall Length allowing for Corners, Ends, Spaces and Openings

Rough Estimate Only Rough Estimate Only. Allow extra for plates, noggings and waste.

Total Length ft =
Stud Centers
?
Assumes Nominal 2 x 4 = Actual size 1~1/2" x 3~1/2"
Assumes Nominal 2 x 6 = Actual size 1~1/2" x 5~1/2"
Studs 		Nominal
Stud Height
?
Bottom Plate - Top Plate - Double Tops and allowance for noggings - Same size as studs - Each plate is equal to wall length
Plates 		Bottom, Top, Double etc
Add Studs per Corner →
Corners
?
Wall Ends - Adds 1 stud per End
Ends 		Adds 1 stud per End
?
Full height space - Adds 1 stud per Space
Spaces 		Adds 1 stud per Space
?
Windows, Doors etc - Adds 2 studs per Opening
Openings 		Adds 2 per Opening
Cost $ Studs and Plates
Length











DON'T BREATH THE DUST If you're cutting blocks, concrete, stone or ANYTHING and there's DUST - DON'T TAKE THE RISK
Don't cut it, or cut it wet so there's NO DUST - Silicosis Sucks
And if you're cutting wet, wear a mask - theres dust in the spray mist too!

How should we spell it?



Results


Built something using our calculators? Please Send Photos! See examples

Blue Dragon Childrens Foundation If you've benefited from this free service please consider supporting Blue Dragon Children's Foundation



Please help promote this free service - Tell a Friend about this site!

Create PDF to print diagrams on this page. Help Printing Help (new window)

Copy all diagrams on this page to bottom of page - Make multiple copies to Print or Compare.

View page on Phone via QR Code (Not current calculation result)

Directory


?
Click Slider to select then use keyboard cursor keys ◄ ► to fine tune.
Use Keyboard ◄ ►
to Fine tune Sliders

?
Create and Print Full Scale PDFs with diagrams on this page (templates)


?
Copy all diagrams on this page to bottom of page - Make multiple copies to Print or Compare Results





PDF & Printing Help

Help Share

← Remove Margins

Jump to Top ↑

Built something using this site?
Please Send Photos!
See Examples
blocklayer.com calculators

If you've benefited from this free service please consider supporting: Please help us support Blue Dragon Children's Foundation




Inch or Metric? 👈
The main Navigation tabs at top of each page are Metric - inputs in millimeters (mm)
Directly under the main tab is a smaller 'Inch' tab for the Feet and Inch version.
Drop Down Menus have M for Metric Versions.
Metric
Calculator
Inch



Please help promote this free service
Tell a Friend!

Facebook Twitter eMail Pinterest Reddit LinkedIn
Contact Us

blocklayer.com calculators

Real Life Online On-Site Calculators with To Scale and Full Scale Animated Detailed Diagrams and Printable Templates
for all Construction Tasks + Woodwork Metal Work and Craft

All calculators on this site are geometric only.
Check relevant local regulations for appropriate sizes, spacings and all engineering requirements.

Disclaimer   |   Privacy & Cookie Policy

Copyright © 2021 - blocklayer.com
Contact Us